• Courses
  • Apps
  • Bulletins
  • Resources
    • Videos
  • Pool Tech Locator
  • About
    • Testimonials
  • Contact
Pool Chemistry Training InstitutePool Chemistry Training Institute
Pool Chemistry Training InstitutePool Chemistry Training Institute
  • Courses
  • Apps
  • Bulletins
  • Resources
    • Videos
  • Pool Tech Locator
  • About
    • Testimonials
  • Contact
Smoke on the Water and Ash in the Pool

Smoke on the Water and Ash in the Pool

Posted by proserve No Comments

The wildfires and resulting ash in the Western states have been devastating for sure and the resulting ash can be carried for long distances and might be getting into many pools and spas.

Service techs and retail stores want to know how to deal with the ash. What does ash in pool/spa water do chemically? Can it be dangerous? What should service techs do? How badly can it mess up water balance? What should retailers tell their customers? Or, is it a problem at all? How concerned should we be?

Learning a little about fire and wildfires will help to understand what we are dealing with and that will lead us to a plan for handling it.

Burning Transforms Fuel into Ash

When something burns, it transforms that fuel into materials with different physical and chemical properties. One of the materials is ash which is the particulate residue remaining on the ground or carried in the thermal wind currents around the wildfire.

The quantity and characteristics of the ash produced depend on:

  1. The quantity of what was burned
  2. The type of material burned (forest, homes, other structures)
  3. The combustion completeness (burning temperature)

 

What’s in the Ash Depends on the Temperature of the Fire

At low combustion completeness temperatures < 840° F, ash is high in organic carbon. This is called pyrogenic carbon. Not important, I just thought it sounds cool.

At high combustion completeness temperature > 840° F, most of the organic carbon is volatilized and the remaining mineral ash has an elevated pH when in water. It is composed mainly of calcium, magnesium, sodium, potassium, silicon, and phosphorous in the form of inorganic carbonates.

At very high combustion completeness temperature > 1076° F most forms are oxides. This has a high pH of 11.0+. Ash produced at lower combustion completeness temperature is usually darker, coarser, and less dense. High-temperature ash is mostly white and less dense.

 

Chemical Characterization

The big constituents of ash from burning forests are, in order, sulfate, ammonia, phosphate, nitrate, naphthalene, biphenyl, iron, copper, calcium, magnesium, sodium, chloride, silica, with a pH of about 11.0. The constituents change when houses and other structures burn and when fire-fighting efforts spray or drop flame-retardant chemicals. But I could not find a complete analysis of ash from a combination of homes, structures, and forests.

Fire Retardant sprayed on pool 091620 1

The fire retardant is mono- or di-ammonium phosphate. So, it depends on how much gets in the pool. And don’t forget that ash doesn’t weigh much. After all, the ash got there in the wind. A 15,000-gallon pool is 125,000 lbs of water. One ppm is about 2 oz. Ash is alkaline so the pH may be high. Phosphates may go up depending on fuel and temperature. Ammonia and chloramines may go up too.

Not all of the ash is soluble. Much of it will remain insoluble. However, it is ash and it is fragile. It can “break” into smaller particles. Think of a piece of paper burning. The resulting ash is usually a few large pieces but if you try to pick it up

or even blow on it and it breaks into many smaller particles. Same thing in the pool water. When that ash hits the pump impeller that is spinning at 1,000 to 3,400 RPM guess what happens? Yep, hundreds or thousands of smaller particles. The pieces may be smaller than the filter can remove. So they can go right through the filter and return to the pool.

Course of Action

The first thing to do is to rinse off surrounding structures, landscaping, and decks. The reason is that a high wind or some rain will wash all of the ash from everything and it may get into the pool water. Please wear goggles and masks and other protective gear.

  1. Now, turn off the pump,
  2. Skim or bag slowly so you don’t break up the ash
  3. Clean the skimmer basket and pump strainer basket
  4. Turn on the pump,
  5. Check the pressure gauge, backwash or clean the filter if needed,
  6. Check the water level and refill to the middle of the skimmer opening
  7. Vacuum to waste (slowly as ash can break apart or re-distribute in water above the vac),
  8. Adjust water balance: pH 7.4-7.6 and TA 80-100 ppm,
  9. Check sanitizer (usually chlorine) and raise to 10 ppm to shock.
  10. Run the pump 24/7 for 3-4 days and check the pressure gauge frequently.

 

Check phosphates and if high (>500 ppm), use a phosphate remover.

If water is cloudy after the above procedure, use a polymer or chitin clarifier or floc with alum. Enzymes can be helpful to remove oils and hydrocarbons.

A sock or shield in the skimmer can help if ash has broken apart.

If there is a huge amount of ash in the pool or if the ash is mostly from man-made materials, it may be better to drain and refill.

I tried to make this short to give you some ideas. If you have suggestions or can add anything to this to make it better, please let me know.

 

DOWNLOAD THIS BULLETIN AS PDF

No Comments
Share
2

You also might be interested in

Borate Dose Calculation Charts for pools

Borate Dose Calculation Charts for pools

Oct 14, 2020

Borate Changes to pH, Total Alkalinity, TDS and Acid to[...]

Bromine or Chlorine? What’s in Your Pool?

Bromine or Chlorine? What’s in Your Pool?

Oct 14, 2020

This happens more than I realized. Many chemical manufacturers use[...]

2.0 to 4.0 Free Chlorine May Not Work

2.0 to 4.0 Free Chlorine May Not Work

Oct 14, 2020

PHTA Guideline and Health Codes May Be Inadequate The PHTA[...]

Leave a Reply

Your email is safe with us.
Cancel Reply

You must be logged in to post a comment.

Recent Posts

  • Pool Ionizer Information
  • Adjusting pH and Alkalinity in Swimming Pools
  • Does Alum Remove CYA in Pools?
  • Pre-Conversion Check Borate Method for Existing Pools
  • Smoke on the Water and Ash in the Pool

About Us

Pool Chemistry Training Institute provides books and courses for residential pool service technicians. We have the experience and the credentials that we impart to all of our trainees for pool chemistry certification.

Quick Links

  • Pool Service Courses
  • Pool Service Apps
  • Pool Service Books
  • Pool Chemical Videos
  • Pool Tech Locator
  • Technical Bulletins
  • Testimonials

© 2025 · Pool Chemistry Training Institute
Website Info

  • Disclaimer
  • Privacy Policy
  • About